FreePBX Pastebin

ADIT 600 Config

From Albert, 1 Day ago, written in Plain Text, viewed 1 times. This paste will go to meet its maker in 3 Weeks.
URL https://pastebin.freepbx.org/view/6b178fcc Embed
Download Paste or View Raw
  1. > print config 6
  2. set verification off
  3. -set 6 password view   {password}  is manual
  4. -set 6 password config {password}  is manual
  5. -set 6 password admin  {password}  is manual
  6. -set 6 enhanced security enable     is manual
  7. -set 6 password security {password} is manual
  8. delete 6 remote "RemoteUnit"
  9. set 6:1 ip address 172.18.5.2 255.255.255.0
  10. set 6:1 gateway 172.18.5.1
  11. set 6:1 up
  12. set 6 syslog level 5
  13. set 6 syslog server 172.18.5.4
  14. set 6 syslog enable
  15. set 6 cdr enable
  16. set 6 log last
  17. set 6 sip gatewayid 172.18.5.2
  18. set 6 sip expires 60
  19. set 6 sip proxy server 172.18.5.4
  20. set 6 sip contactaddress gatewayid
  21. set 6 sip viaaddress gatewayid
  22. set 6 voip rtp baseport 19999
  23. set 6 voip payload type lenient
  24. set 6 voip g729a disable
  25. set 6:1:1:1-48 algorithm preference g711mu g711a g726_16 g726_24 g726_32 \
  26. g726_40
  27. set 6:1:1:1 userid "001" "001"
  28. set 6:1:1:1 authentication "001" "123456"
  29. set 6:1:1:2 userid "002" "002"
  30. set 6:1:1:2 authentication "002" "654321"
  31. reset 6
  32.  
  33.  
  34. > print config
  35.  
  36. -------------------------------------------------------------
  37. -Adit 600 configuration file
  38. -Created on 04/22/2026 at 16:06:17
  39. -This file is valid for the following configuration only:
  40. -
  41. -        CardType
  42. -        --------
  43. -SLOT A   T1x2         SW Version:10.1.2.2
  44. -SLOT 1   FXS8Ax8  
  45. -SLOT 2   FXS8Ax8  
  46. -SLOT 3   4WE&Mx4  
  47. -SLOT 4   FXS8Cx8  
  48. -SLOT 5   OCUDPx4  
  49. -SLOT 6   CMGx1    
  50. -NOTES:
  51. -1. It is necessary to issue the commands 'restore defaults'
  52. -   and 'reset' BEFORE downloading the configuration file to
  53. -   ensure proper configuration.
  54. -2. Lines beginning with '-' will be ignored as comments
  55. -   by the CLI.  Before downloading, review the sections of
  56. -   the configuration file delimited by these comments and
  57. -   delete the commands that are not needed (e.g. 'set ip
  58. -   address' and 'add user' are likely candidates for
  59. -   deletion).
  60. -3. While downloading, a character delay of 5 ms and a line
  61. -   delay of 500 ms is recommended.
  62. -4. Small build running on 16M of Ram.
  63.  
  64. -------------------------------------------------------------
  65.  
  66. -Notes
  67.  
  68. set notes 1 ""
  69.  
  70.  
  71. -Turning off verification messages.
  72.  
  73. set verification off
  74.  
  75. -Setting local off.
  76.  
  77. set local off
  78.  
  79. -Disconnecting all connections.
  80.  
  81. disconnect a
  82. disconnect 1
  83. disconnect 2
  84. disconnect 3
  85. disconnect 4
  86. disconnect 5
  87. disconnect 6
  88.  
  89. -Setting IP addresses.
  90.  
  91. set ethernet ip address 172.18.5.3 255.255.255.0
  92. set ip gateway 172.18.5.1
  93.  
  94. -Setting the SNMP MIB-II System Group objects.
  95.  
  96. set snmp getcom "public"
  97. set snmp setcom "public"
  98. set snmp trapcom "public"
  99. set snmp trapauth enable
  100. set snmp trapevent all
  101.  
  102.  
  103.  
  104. -Setting slot a.
  105.  
  106. set a:1 up
  107. set a:1 fdl none
  108. set a:1 lbo 1
  109. set a:1 framing esf
  110. set a:1 id "20_MediumBooms p4"
  111. set a:1 linecode b8zs
  112. set a:1 loopdetect csu
  113. set a:1 ais disable
  114. set a:1:1-2 side drop
  115. set a:1:1-2 type voice
  116. set a:1:1-2 signal emi
  117. set a:1:3-8 side drop
  118. set a:1:3-8 type voice
  119. set a:1:3-8 signal ls
  120. set a:1:9-10 side drop
  121. set a:1:9-10 type voice
  122. set a:1:9-10 signal plar
  123. set a:1:11-24 side drop
  124. set a:1:11-24 type voice
  125. set a:1:11-24 signal ls
  126. set a:2 down
  127. set a:2 fdl none
  128. set a:2 lbo 1
  129. set a:2 framing esf
  130. set a:2 id "CAC DS1# A:2"
  131. set a:2 linecode b8zs
  132. set a:2 loopdetect csu
  133. set a:2 ais disable
  134. set a:2:1 side drop
  135. set a:2:1 type voice
  136. set a:2:1 signal emi
  137. set a:2:2-24 side drop
  138. set a:2:2-24 type voice
  139. set a:2:2-24 signal ls
  140.  
  141. -Setting slot 1.
  142.  
  143. set 1:1 signal lsrb
  144. set 1:1 txgain -3
  145. set 1:1 rxgain -6
  146. set 1:1 impedance 19
  147. set 1:2-8 signal ls
  148. set 1:2-8 txgain -3
  149. set 1:2-8 rxgain -6
  150. set 1:2-8 impedance 19
  151.  
  152. -Setting slot 2.
  153.  
  154. set 2:1-8 signal ls
  155. set 2:1-8 txgain -3
  156. set 2:1-8 rxgain -6
  157. set 2:1-8 impedance 19
  158.  
  159. -Setting slot 3.
  160.  
  161. set 3:1 txgain 0
  162. set 3:1 rxgain 0
  163. set 3:1 signal emi
  164. set 3:1 type voice
  165. set 3:2 txgain 0
  166. set 3:2 rxgain 0
  167. set 3:2 signal emi
  168. set 3:2 type voice
  169. set 3:3 txgain 0
  170. set 3:3 rxgain 0
  171. set 3:3 signal emi
  172. set 3:3 type voice
  173. set 3:4 txgain 0
  174. set 3:4 rxgain 0
  175. set 3:4 signal emi
  176. set 3:4 type voice
  177.  
  178. -Setting slot 4.
  179.  
  180. set 4:1-4 signal ls
  181. set 4:1-4 txgain 0
  182. set 4:1-4 rxgain 0
  183. set 4:1-4 impedance 19
  184. set 4:1-4 cpd 2000
  185. set 4:5-8 signal ls
  186. set 4:5-8 txgain -3
  187. set 4:5-8 rxgain -6
  188. set 4:5-8 impedance 19
  189. set 4:5-8 cpd 2000
  190.  
  191. -Setting slot 5.
  192.  
  193. set 5:1 down
  194. set 5:1 baud 56000
  195. set 5:1 loopdetect csu llb enable
  196. set 5:1 loopdetect dsu llb enable
  197. set 5:1 loopdetect ocu llb enable
  198. set 5:1 mvec disable
  199. set 5:1 secondary disable
  200. set 5:2 down
  201. set 5:2 baud 56000
  202. set 5:2 loopdetect csu llb enable
  203. set 5:2 loopdetect dsu llb enable
  204. set 5:2 loopdetect ocu llb enable
  205. set 5:2 mvec disable
  206. set 5:2 secondary disable
  207. set 5:3 down
  208. set 5:3 baud 56000
  209. set 5:3 loopdetect csu llb enable
  210. set 5:3 loopdetect dsu llb enable
  211. set 5:3 loopdetect ocu llb enable
  212. set 5:3 mvec disable
  213. set 5:3 secondary disable
  214. set 5:4 down
  215. set 5:4 baud 56000
  216. set 5:4 loopdetect csu llb enable
  217. set 5:4 loopdetect dsu llb enable
  218. set 5:4 loopdetect ocu llb enable
  219. set 5:4 mvec disable
  220. set 5:4 secondary disable
  221.  
  222. -Setting slot 6.
  223.  
  224. set 6 proxy disable
  225. set 6 network info disable
  226. set 6 default
  227. - CMG configuration occurs after connects
  228.  
  229. -Setting password length.
  230.  
  231. set password length long
  232.  
  233. -Setting primary and secondary clock sources.
  234.  
  235. set clock1 a:1
  236. set clock2 a:1
  237.  
  238. -Setting the system idle pattern for DS0s.
  239.  
  240. set idle 0x0
  241.  
  242. -Setting NTP options.
  243.  
  244. set ntp server address 172.18.5.4
  245. set ntp timezone -5 0
  246.  
  247. -Making connections.
  248.  
  249. connect 2:1-2 6:1:1:1-2
  250. connect 3:1 3:2
  251. connect 3:3 3:4
  252.  
  253. -Setting slot 6 CMG.
  254.  
  255. set verification off
  256. -set 6 password view   {password}  is manual
  257. -set 6 password config {password}  is manual
  258. -set 6 password admin  {password}  is manual
  259. -set 6 enhanced security enable     is manual
  260. -set 6 password security {password} is manual
  261. delete 6 remote "RemoteUnit"
  262. set 6:1 ip address 172.18.5.2 255.255.255.0
  263. set 6:1 gateway 172.18.5.1
  264. set 6:1 up
  265. set 6 syslog level 5
  266. set 6 syslog server 172.18.5.4
  267. set 6 syslog enable
  268. set 6 cdr enable
  269. set 6 log last
  270. set 6 sip gatewayid 172.18.5.2
  271. set 6 sip expires 60
  272. set 6 sip proxy server 172.18.5.4
  273. set 6 sip contactaddress gatewayid
  274. set 6 sip viaaddress gatewayid
  275. set 6 voip rtp baseport 19999
  276. set 6 voip payload type lenient
  277. set 6 voip g729a disable
  278. set 6:1:1:1-48 algorithm preference g711mu g711a g726_16 g726_24 g726_32 \
  279. g726_40
  280. set 6:1:1:1 userid "001" "001"
  281. set 6:1:1:1 authentication "001" "123456"
  282. set 6:1:1:2 userid "002" "002"
  283. set 6:1:1:2 authentication "002" "654321"
  284. reset 6
  285.  
  286.  
  287.  
  288. -Turning verification on.
  289.  
  290. set verification on
  291.  
  292. -Turning autoexit on.
  293.  
  294. set autoexit on
  295.  

Reply to "ADIT 600 Config"

Here you can reply to the paste above

Sangoma Terms of Use & Policies

Powered by Stikked