> print config 6
set verification off
-set 6 password view   {password}  is manual
-set 6 password config {password}  is manual
-set 6 password admin  {password}  is manual
-set 6 enhanced security enable     is manual
-set 6 password security {password} is manual
delete 6 remote "RemoteUnit"
set 6:1 ip address 172.18.5.2 255.255.255.0
set 6:1 gateway 172.18.5.1
set 6:1 up
set 6 syslog level 5
set 6 syslog server 172.18.5.4
set 6 syslog enable
set 6 cdr enable
set 6 log last 
set 6 sip gatewayid 172.18.5.2
set 6 sip expires 60
set 6 sip proxy server 172.18.5.4
set 6 sip contactaddress gatewayid
set 6 sip viaaddress gatewayid
set 6 voip rtp baseport 19999
set 6 voip payload type lenient
set 6 voip g729a disable
set 6:1:1:1-48 algorithm preference g711mu g711a g726_16 g726_24 g726_32 \
g726_40 
set 6:1:1:1 userid "001" "001"
set 6:1:1:1 authentication "001" "123456"
set 6:1:1:2 userid "002" "002"
set 6:1:1:2 authentication "002" "654321"
reset 6 


> print config

-------------------------------------------------------------
-Adit 600 configuration file
-Created on 04/22/2026 at 16:06:17 
-This file is valid for the following configuration only:
-
-        CardType
-        --------
-SLOT A   T1x2         SW Version:10.1.2.2
-SLOT 1   FXS8Ax8   
-SLOT 2   FXS8Ax8   
-SLOT 3   4WE&Mx4   
-SLOT 4   FXS8Cx8   
-SLOT 5   OCUDPx4   
-SLOT 6   CMGx1     
-NOTES:
-1. It is necessary to issue the commands 'restore defaults'
-   and 'reset' BEFORE downloading the configuration file to
-   ensure proper configuration.
-2. Lines beginning with '-' will be ignored as comments
-   by the CLI.  Before downloading, review the sections of
-   the configuration file delimited by these comments and
-   delete the commands that are not needed (e.g. 'set ip
-   address' and 'add user' are likely candidates for
-   deletion).
-3. While downloading, a character delay of 5 ms and a line
-   delay of 500 ms is recommended.
-4. Small build running on 16M of Ram.

-------------------------------------------------------------

-Notes

set notes 1 ""


-Turning off verification messages.

set verification off

-Setting local off.

set local off

-Disconnecting all connections.

disconnect a
disconnect 1
disconnect 2
disconnect 3
disconnect 4
disconnect 5
disconnect 6

-Setting IP addresses.

set ethernet ip address 172.18.5.3 255.255.255.0
set ip gateway 172.18.5.1

-Setting the SNMP MIB-II System Group objects.

set snmp getcom "public"
set snmp setcom "public"
set snmp trapcom "public"
set snmp trapauth enable
set snmp trapevent all



-Setting slot a.

set a:1 up
set a:1 fdl none
set a:1 lbo 1
set a:1 framing esf
set a:1 id "20_MediumBooms p4"
set a:1 linecode b8zs
set a:1 loopdetect csu
set a:1 ais disable
set a:1:1-2 side drop
set a:1:1-2 type voice
set a:1:1-2 signal emi
set a:1:3-8 side drop
set a:1:3-8 type voice
set a:1:3-8 signal ls
set a:1:9-10 side drop
set a:1:9-10 type voice
set a:1:9-10 signal plar
set a:1:11-24 side drop
set a:1:11-24 type voice
set a:1:11-24 signal ls
set a:2 down
set a:2 fdl none
set a:2 lbo 1
set a:2 framing esf
set a:2 id "CAC DS1# A:2"
set a:2 linecode b8zs
set a:2 loopdetect csu
set a:2 ais disable
set a:2:1 side drop
set a:2:1 type voice
set a:2:1 signal emi
set a:2:2-24 side drop
set a:2:2-24 type voice
set a:2:2-24 signal ls

-Setting slot 1.

set 1:1 signal lsrb
set 1:1 txgain -3
set 1:1 rxgain -6
set 1:1 impedance 19
set 1:2-8 signal ls
set 1:2-8 txgain -3
set 1:2-8 rxgain -6
set 1:2-8 impedance 19

-Setting slot 2.

set 2:1-8 signal ls
set 2:1-8 txgain -3
set 2:1-8 rxgain -6
set 2:1-8 impedance 19

-Setting slot 3.

set 3:1 txgain 0
set 3:1 rxgain 0
set 3:1 signal emi
set 3:1 type voice
set 3:2 txgain 0
set 3:2 rxgain 0
set 3:2 signal emi
set 3:2 type voice
set 3:3 txgain 0
set 3:3 rxgain 0
set 3:3 signal emi
set 3:3 type voice
set 3:4 txgain 0
set 3:4 rxgain 0
set 3:4 signal emi
set 3:4 type voice

-Setting slot 4.

set 4:1-4 signal ls
set 4:1-4 txgain 0
set 4:1-4 rxgain 0
set 4:1-4 impedance 19
set 4:1-4 cpd 2000
set 4:5-8 signal ls
set 4:5-8 txgain -3
set 4:5-8 rxgain -6
set 4:5-8 impedance 19
set 4:5-8 cpd 2000

-Setting slot 5.

set 5:1 down
set 5:1 baud 56000
set 5:1 loopdetect csu llb enable
set 5:1 loopdetect dsu llb enable
set 5:1 loopdetect ocu llb enable
set 5:1 mvec disable
set 5:1 secondary disable
set 5:2 down
set 5:2 baud 56000
set 5:2 loopdetect csu llb enable
set 5:2 loopdetect dsu llb enable
set 5:2 loopdetect ocu llb enable
set 5:2 mvec disable
set 5:2 secondary disable
set 5:3 down
set 5:3 baud 56000
set 5:3 loopdetect csu llb enable
set 5:3 loopdetect dsu llb enable
set 5:3 loopdetect ocu llb enable
set 5:3 mvec disable
set 5:3 secondary disable
set 5:4 down
set 5:4 baud 56000
set 5:4 loopdetect csu llb enable
set 5:4 loopdetect dsu llb enable
set 5:4 loopdetect ocu llb enable
set 5:4 mvec disable
set 5:4 secondary disable

-Setting slot 6.

set 6 proxy disable
set 6 network info disable
set 6 default
- CMG configuration occurs after connects

-Setting password length.

set password length long

-Setting primary and secondary clock sources.

set clock1 a:1
set clock2 a:1

-Setting the system idle pattern for DS0s.

set idle 0x0

-Setting NTP options.

set ntp server address 172.18.5.4
set ntp timezone -5 0

-Making connections.

connect 2:1-2 6:1:1:1-2
connect 3:1 3:2
connect 3:3 3:4

-Setting slot 6 CMG.

set verification off
-set 6 password view   {password}  is manual
-set 6 password config {password}  is manual
-set 6 password admin  {password}  is manual
-set 6 enhanced security enable     is manual
-set 6 password security {password} is manual
delete 6 remote "RemoteUnit"
set 6:1 ip address 172.18.5.2 255.255.255.0
set 6:1 gateway 172.18.5.1
set 6:1 up
set 6 syslog level 5
set 6 syslog server 172.18.5.4
set 6 syslog enable
set 6 cdr enable
set 6 log last 
set 6 sip gatewayid 172.18.5.2
set 6 sip expires 60
set 6 sip proxy server 172.18.5.4
set 6 sip contactaddress gatewayid
set 6 sip viaaddress gatewayid
set 6 voip rtp baseport 19999
set 6 voip payload type lenient
set 6 voip g729a disable
set 6:1:1:1-48 algorithm preference g711mu g711a g726_16 g726_24 g726_32 \
g726_40 
set 6:1:1:1 userid "001" "001"
set 6:1:1:1 authentication "001" "123456"
set 6:1:1:2 userid "002" "002"
set 6:1:1:2 authentication "002" "654321"
reset 6 



-Turning verification on.

set verification on

-Turning autoexit on.

set autoexit on